How to Hard Reset Your Router

Hard reset Linksys E900

by

Posted on April 4th, 2013


Linksys E900
Factory reset (Hard reset) Locate the button at the bottom of the router, then press and hold this button for 5-10 seconds (until the port lights flash at the same time).
Firmware Link to support
Default username [leave blank]
Default password admin
Default IP address 192.168.1.1

Read More

Hard reset D-Link DIR-665

by

Posted on April 4th, 2013


D-Link DIR-665
Factory reset (Hard reset) Power On the router. Locate the reset pin hole on the back. Use a sharp object to press it and hold it down for 5 seconds. Release. ... Important: If that does not work, try pressing the button and holding it down for 10 seconds, release.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset Linksys WRT160NL

by

Posted on April 4th, 2013


Linksys WRT160NL
Factory reset (Hard reset) Locate the reset button on the right side of the product label(on the bottom of the router). Press and hold the reset button for approximately 5 seconds, unplug and replug the router.
Specifications
Manual
Firmware Link to support
Default username [leave blank]
Default password admin
Default IP address 192.168.1.1

Read More

Hard reset D-Link DI-804HV

by

Posted on April 4th, 2013


D-Link DI-804HV
Factory reset (Hard reset) Turn OFF the router. Locate the reset pin hole on the back panel. Use a paper clip to press it and hold down for only about 5 seconds - don't hold too long. Release. (You can also watch the lights on the front cover - it is time to release the button when M1 and M2 flash at the same time.)
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-300

by

Posted on April 4th, 2013


D-Link DIR-300
Factory reset (Hard reset) The reset button/hole is located on the back panel - to the right. Power on the router and use a paper clip or another sharp object to press the button down and hold for 10 seconds. Release. Wait about 30 seconds for the reboot process to finish.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-link DIR-130

by

Posted on April 4th, 2013


D-Link DIR-130
Factory reset (Hard reset) Power on the router. Find the reset "hole" on the back panel. Use a paper clip to press and hold the button down for 10 seconds. Release and wait about 30 seconds for the router to reboot. 
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-457

by

Posted on April 4th, 2013


D-Link DIR-457
Factory reset (Hard reset) First open the back cover of your DIR-457 router. The reset pin hole is around the middle, next to the MicroSD card slot - check the picture above. Press the reset 'hole' button with a sharp object (paperclip) and hold for 5 seconds until the device restarts.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-330

by

Posted on April 4th, 2013


D-Link DIR-330
Factory reset (Hard reset) Find the reset button on the back panel of the router. It is actually a reset 'hole' so you will need a sharp object to press it down - a paper clip would do the job. Press and hold the button down for 10 seconds then release. Wait 30 seconds for the reboot process to finish. Your router is now set back to it's default settings. 
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-628

by

Posted on April 3rd, 2013


D-Link DIR-628
Factory reset (Hard reset) Power on the router and press the reset button for 10 seconds. The reset button is located on the back of the router - it is placed in a small hole so you will probably need a sharp object (like a paperclip) to press and hold it down. Release and wait about 30 seconds for the router to reboot.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-855

by

Posted on April 3rd, 2013


D-Link DIR-855
Factory reset (Hard reset) This router has a reset "hole" which is located on the back panel (next to the USB port). The router must be switched on. Use a sharp object such as a paperclip to press and hold the button (in the hole) down for 10 seconds. Release and wait about 30 seconds.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More