How to Hard Reset Your Router

Hard reset D-Link DHP-1565

by

Posted on April 4th, 2013


D-Link DHP-1565
Factory reset (Hard reset) Power ON the router. Locate the reset button hole on the back panel. Use a paper clip to press it and hold down for 5 seconds. Release. Wait about 30-60 seconds for the reboot process to finish. PS. The power LED on the front panel lights up in orange during the factory reset process.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-645

by

Posted on April 4th, 2013


D-Link DIR-645
Factory reset (Hard reset) The factory reset button hole is located on the bottom of the router - check the picture above. Power ON the router. Use a thin object (paperclip) to press and hold down the button for 10 seconds. Release. Wait about 30-60 seconds before accessing the router.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-827

by

Posted on April 4th, 2013


D-Link DIR-827
Factory reset (Hard reset) Power ON the router. Locate the reset pin hole - it is on the back panel (next to the USB port) and is marked with red. Use a paper clip to press and hold down the button for 10 seconds. Release. Wait 30-60 seconds to access the router. 
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

How to hard reset a D-Link router to the default settings

by

Posted on April 4th, 2013


If you’ve forgotten your D-Link router’s username/password or if someone has changed them without telling you, you can always reset your router to it’s default username and password. Keep in mind that this process will change all of your settings back to the defaults, so it is a good idea to keep a backup of your router’s configuration if you have a more complicated set-up.

The Hard Reset Process

For most of the D-Link routers the resetting process goes like this:

1. Power ON the router. Unplug all of the cables, except the power cord.

2. Locate the reset button
Usually, the reset button is a small ‘pin hole’ ¬†that you can find on the rear panel of the router. It might be red, or marked with a red/white/gray circle.

3. Take e thin/sharp object, such as a paper clip. Put it into the reset hole. Now press and hold for 10 seconds. Release.

4. The reboot process begins and it takes about 30-60 seconds.

D-Link Default Settings

Once your router has been reset, it goes back to it’s factory defaults.

(more…)

Hard reset D-Link DIR-865L

by

Posted on April 4th, 2013


D-Link DIR-865L
Factory reset (Hard reset) Power ON the router. The reset button 'hole' is located on the side of the router (above the power switch) and is marked with red. Press in the hole with a thin object and hold for 6 seconds. Release. Wait for 1 min for the router to reboot.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-651

by

Posted on April 4th, 2013


D-Link DIR-651
 
Factory reset (Hard reset) Power ON the router. The reset button 'hole' is located on the back panel of the router - to the right of the right antenna. Press in it with a thin object (paperclip) and hold for about 10 seconds. Release. Wait for a minute until the router reboots.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-857

by

Posted on April 4th, 2013


D-Link DIR-857
Factory reset (Hard reset) Power ON the device. The reset hole is located on the back panel of the router, it is marked with red. Press in it with a thin object and hold for 10 seconds. Release. Wait for 1 min for the router to reboot.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-605L

by

Posted on April 4th, 2013


D-Link DIR-605L
Factory reset (Hard reset) Power ON the router. The reset "hole" is located on the back of the router - to the right side of the right antenna. Use a thin object to press in and hold down for 10 seconds. Release. Wait a minute until the router reboots.
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DGL-4500

by

Posted on April 4th, 2013


D-Link DGL-4500
Factory reset (Hard reset) Power ON the router. Locate the reset pin hole on the back (next to the USB port). Press it with a thin object (paperclip) and hold down for 5-10 seconds. Release and wait for 30-60 seconds for the reboot process to finish.
Specifications
Manual
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-825

by

Posted on April 4th, 2013


D-Link DIR-825
Factory reset (Hard reset) Power ON the router. The reset button is the small hole on the back panel - use a paperclip to hold it down for 10 seconds. Release. Wait 30 sec - 1 min for the reboot process to finish.
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More