How to Hard Reset Your Router

Hard reset D-Link DGL-4300

by

Posted on April 18th, 2013


D-Link DGL-4300
Factory reset (Hard reset) Power ON the router. Locate the hard reset button hole on the back side. Put a paper clip in the hole and press down. Watch the LEDs on the front panel and release when all of them blink at the same time. Wait for the router to reboot (30sec - 1min).
Specifications
Manual
Firmware Link to support
Default username [none]
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-515

by

Posted on April 16th, 2013


D-Link DIR-515
Factory reset (Hard reset) Turn the router ON and locate the reset pin hole on the back panel. Use a paper clip to press in it and hold for 10 seconds. Release. Wait at least 30 seconds before trying to access the router.
Specifications
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-501

by

Posted on April 16th, 2013


D-Link DIR-501
Factory reset (Hard reset) Power ON your router. Locate the reset button hole on the rear panel. Use a paperclip to press the button and hold it down for 10 seconds. Release. Wait for a minute until the reset process has finished.
Specifications
Manual
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DAP-1560 access point

by

Posted on April 16th, 2013


D-Link DAP-1560
Factory reset (Hard reset) Power ON the access point. The reset button hole is on the back panel. Press in it with a thin object and hold for 10 seconds. Release. Wait for 30sec - 1min before accessing the device.
Specifications
Default username admin
Default password [leave blank]
Default IP address 192.168.0.50

Read More

Hard reset D-Link DIR-657

by

Posted on April 16th, 2013


D-Link DIR-657
Factory reset (Hard reset) The reset button hole is on the back panel and is marked with red. Press it down with a thin object and hold for 10 seconds. Release. Wait a minute for the router to reboot.
Specifications
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

Hard reset D-Link DIR-636L

by

Posted on April 16th, 2013


D-Link DIR-636L
Factory reset (Hard reset) Locate the reset button hole on the bottom of the device. Use a thin (sharp) object to press and hold the button down for 10 seconds. Wait for the router to reboot.
Specifications
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Read More

I spilled water on my router – what to do now?

by

Posted on April 12th, 2013


Spilling water on your electronic devices is always a very unfortunate event. However, if you act very quickly you have a chance to save the device. When I say quickly I mean right away.

I am going to talk about routers here, but the same goes for modems and switches.

After spilling water on your router

1. React very quickly

Especially if the router was plugged in and working when the incident happened.

(more…)

Hard reset TP-LINK AC1750

by

Posted on April 10th, 2013


TP-LINK AC1750
Factory reset (Hard reset) Locate the WPS/Reset button at the back of the router. With the device powered on press and hold the button for approximately 8 seconds(until SYS LED starts flashing quickly) and release the button.
Specifications
Default username admin
Default password admin
Default IP address 192.168.0.1

Read More

Hard reset Linksys EA6700

by

Posted on April 10th, 2013


Linksys EA6700
Factory reset (Hard reset) Locate the reset button on the back panel of the router. Use a paperclip to press and hold the button for approximately ten seconds then release.
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.1.1

Read More

Hard reset Linksys EA6500

by

Posted on April 10th, 2013


Linksys EA6500
Factory reset (Hard reset) Locate the reset button on the back panel of the router. Use a paperclip to press and hold the button for approximately ten seconds.
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.1.1

Read More