How to Hard Reset Your Router

Hard reset TP-LINK TL-WR841HP

by

Posted on June 7th, 2013


TP-LINK TL-WR841HP
Factory reset (Hard reset) Power ON the router. Locate the WPS/RESET button on the back panel of the device. Press and hold the button for more than 5 seconds. Keep an eye on the system LED and when it starts flashing more quickly than before - release. Wait for the router to reboot.  
PS. The system LED is the second led on the front panel - it is right next to the power LED.
Specifications
Manual
Default username admin
Default password admin
Default IP address 192.168.0.1

Read More

Hard reset TP-LINK TL-WR710N

by

Posted on May 19th, 2013


TP-LINK TL-WR710N
Factory reset (Hard reset) Power ON the router and locate the reset button hole on the bottom of the device. Use a pin to press inside the hole and hold for about 5-6 seconds. Keep an eye on the blue LED on the side of the router - release the reset button when the LED starts blinking. Wait for the router to reboot - when it's ready to use the LED will stop blinking.
Specifications
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.254

Read More

Hard reset TP-LINK TL-WR702N

by

Posted on May 19th, 2013


TP-LINK TL-WR702N
Factory reset (Hard reset) Power ON the router. The reset button hole is located on the bottom of the device. Use a thin object like a pin to press inside and hold for about 5-6 seconds. Release and wait about 1 minute for the router to reboot and go back to the factory defaults.
Specifications
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.254

Read More

Hard reset TP-LINK TL-WR700N

by

Posted on May 19th, 2013


TP-LINK TL-WR700N
Factory reset (Hard reset) Power ON the router, use a pin to press and hold the RESET button on the bottom of the router for about 5-6 seconds. Then release the button and wait the Router to reboot to its factory default settings.
Specifications
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.254

Read More

Hard reset TP-Link TL-WR720N

by

Posted on May 19th, 2013


TP-LINK TL-WR720N
Factory reset (Hard reset) Power ON the router. Locate the reset button on the back panel - it is labeled WPS/RESET. Press it and hold for at least 5-6 seconds. You should see the System LED blinking faster than usual. When this happens - release the button and wait the router to reboot to its factory default settings. 
PS. The System LED is the second one on the front panel and it looks like a small sun. 
Specifications
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Read More

Hard reset TP-Link TL-WR743ND

by

Posted on May 19th, 2013


TP-LINK TL-WR743ND
Factory reset (Hard reset) There are two different versions of this router: Version 1 has a square body with a big black front panel, while Version 2 has rounded corners and just a little black on the front. Good news is they both reset the same way. Find the reset button hole on the back of the device. Use a pin to press inside the hole and hold for about 5 seconds. Watch the SYS LED - when it starts flashing more quickly than before - release. Wait for a minute for the router to reboot. 
PS: V1 - System LED is labeled SYS. V2 - System LED is the one that looks like a small sun
NB: The default ip address are different for V1 and V2
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address Version 1: 192.168.1.1 -_- Version 2: 192.168.0.1

Read More

Hard reset TP-Link TL-WR741ND

by

Posted on May 19th, 2013


TP-LINK TL-WR741ND
Factory reset (Hard reset) The Reset button is a small hole on the back side of the router. Press in it with a thin object (a paper clip maybe) for five seconds. Then release and wait for the reboot process to finish - up to 1 minute.
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Read More

Hard reset TP-Link TL-WR740N

by

Posted on May 18th, 2013


TP-LINK TL-WR740N
Factory reset (Hard reset) The reset button hole is on the back of the device - it has RESET written under it with hard to notice white letters. Press the Reset button with a thin object (like a paper clip), hold for five seconds and release. Wait for the TP-LINK router to reboot.
Manual
Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Read More

Hard reset NETGEAR R6300

by

Posted on May 2nd, 2013


NETGEAR R6300
Factory reset (Hard reset) Locate the reset button on the back panel - a small hole to the left of the Power ON/OFF button. Use a thin object like a paper clip to push and hold the button for at least 7 seconds. Release and wait for the router to reboot. IMPORTANT: The default wireless network name (SSID) and password are unique for each of the routers of this model - you can find the name and password on the label on the bottom of your router.
Specifications
Manual
Firmware Link to support
Default username admin
Default password password
Default IP address 192.168.1.1

Read More

Hard reset NETGEAR D6300

by

Posted on May 2nd, 2013


NETGEAR D6300
Factory reset (Hard reset) Locate the reset pin hole on the rear panel - to the left of the Power ON/OFF button. Use a paper clip or other thin object to press in the hole and hold for at least 6 seconds. Release. Additional info: the Power LED on the front panel will blink three times in red when you release the reset button. Then it will become green once the default settings are restored.
Specifications
Manual
Default username admin
Default password password
Default IP address 192.168.0.1

Read More